Mitsubishi Heavy FDS Monosplit Unit Set 230V, No. K85552 (Outdoor Unit Inverter FDC71VN (X) + Indoor Unit Tower FDF-VD Model 71), 7.1/8kW, 4.5kW Heating capacity at -15°C

Mitsubishi Heavy FDS Monosplit Unit Set 230V, No. K85552 consists of an outdoor unit Inverter FDC71VN (X) and an indoor unit Tower FDF-VD Model 71), 7.1/8kW, 4.5kW heating power at -15°CMitsubishi Heavy outdoor unit Inverter 230V FDC VN Model 71, No. K87815,7.1/8k Air/air heat pump unit with inverter technology for up to 2 split-climate indoor units in simultaneous operation Ready-for-connection cooling machine unit for outdoor installation for cooling and heating. The components are produced in large series production according to ISO 9001, CE-certified and tested under standard conditions. The device meets the requirements of WHG (outside of water protection areas, below the minimum limit) The housing is self-supporting and consists of a galvanized base frame and easily removable stove-enamelled panels. The "Blue-Fin" coating of the heat exchanger provides protection against corrosion. A power-regulated scroll compressor adjusts its speed to the required capacity The DC inverter compressor is equipped with an oil sump heater, mounted on vibration dampers and protected against overheating and timing. In addition to the compressor u a consisting of the following components: hot gas silencer, oil separator, 4-way switch-over valve, optimised large-area heat exchanger, electronic expansion valves, liquid separator, liquid separator, shut-off valves and Schrader valves High pressure switch, low pressure sensor, temperature sensor. A regulated fan with DC motor ensures low-noise optimization of the condensation temperature. The fully automatic microprocessor control operates systems optimizing and communicates via bus signals with the connected indoor units. Current sensor, Noise Killer, Spark Killer, autom. Oil recirculation and defrost control as well as different coloured LEDs for indication of operating conditions and diagnostics ensure safe operation. The test mode checks the perfect functioning of the system in cooling or heating mode. Pump-down operation can be activated Silent operation ensures soundproof operation Power is supplied via the outdoor unit The electrical connection between the outdoor and indoor unit is 4-wire Technical data: Nominal output cooling / heating: 7.1/8.0 kWcooling / heating: 3.2~8.0/3.6~9.0 kWHeating output at -15°C: 4.5 kWEER Cooling: up to 3.48COP Heating: up to 4.12Power data in accordance with Ecodesign guideline for indoor unit combination: 1 x FDT71VFcooling SE Liquid connection: 10 mm (3/8 ") connector Suction gas capacity: 16 mm (5/8 ") cable length max.: 50height difference, AG higher/lower: 30/15 m Air volume flow rate max.: 3600 m³/hSound pressure level max. Cooling/Heating: 51/48 dB (A) (1 m, JIS standard)Sound power level Cooling/Heating: 66/66 dB (A)Dimensions (H/W/D): 750/968/340 mmNet weight unit: 60 kgIndustrial range Cooling/Heating: -15 to +43 / -20 to +20 °CData outdoor unit dependent on connected indoor unit and based on standard conditionsCooling: outdoor Split indoor unit ready for connection and operation for floor-standing installation for cooling and heating The tower enables an efficient supply of refrigeration and cooling energy. Heating capacity with comparatively small installation area of only 0.192 m² Due to the special device geometry and the high achievable air throw distances, a very good penetration of the room air is possible even in larger rooms. The tower can thus be placed inconspicuously in less exposed places in the room. Due to the flexible electrical and cold side (in 4 directions) connection options, the air conditioner is easy to install or to install. The air intake at the front side is via a regenerative filter, the air outlet via a vibration damped, quiet running 4-stage fan with overheating protection. Fixable blades (vertical) as well as automatic pendulum blades (horizontal) with motor-driven automatic deflector ensure optimum air distribution and a wide spread of the air jet. If required, the adjustable air guide blades can be fixed in a desired position. The device contains all the equipment necessary for automatic operation as well as control and regulating devices. The microprocessor monitors and controls individual components The device has a special control unit for dehumidification The anti-icing protection guarantees optimum heat transfer at the heat exchanger The hot-start and hot-sport function ensure rapid heating of cold rooms after the air conditioner has been started in heating mode. The self-diagnosis system indicates possible faults due to an alphanumeric code on the remote control. The operating mode (cooling, dehumidification, heating, circulating air, automatic mode), setpoint temperature, fan stage and fin pendulum can be programmed. The device can be switched on and off by an external pulse or on/off signal via a potential-free contact Remote On/Off. The device is controlled by an integrated cable remote control or optionally with infrared remote control. The optional CompTrol series increases operating comfort and operational safety through centralized control and monitoring with a connection to central control systems and building management systems Technical data: Nominal output cooling / heating: 7.1/8.0 kWNumber of fan stages: 4 pcs. Liquid connection: 10 mm (3/8 ") connector Suction gas connection: 16 mm (5/8 ") connection Condensate capacity: ID 20/AD 26 mmDimensions (H/W/D).: 1850/600/320 mmNet weight Device: 49 kgData related to standard conditions and depending on outdoor unit Cooling: outside 35°C, room 27°C/47% r. h. Heating: outside 7°C, room 20°C