Mitsubishi Heavy S Monosplit-System 230V, Nr.K85275 (outdoor unit SRC-ZMX model 35 + indoor unit FDTC model 35), 3.5/4.5kW

Mitsutohi Heavy S Monosplit-System 230V, Nr.K85275 consists of a SRC-ZMX model 35 and an indoor unit FDTC model 35 Euro grid ceilings cassette with panel, cooling capacity/heating power 3.5/4.5kW

Mitsutohi Heavy outdoor unit inverter 230V SRC-ZMX model 35, 3.5/4.5kW.
Air / air heat pump unit with inverter technology for split air-indoor units as an extremely compact unit ready for connection chillers lightweight for outdoor installation for heating and cooling with the high-performance refrigerant R410A.
The casing is self-supporting and consists of a sturdy galvanized base frame and easily removable enamelled panels. The parts and sheets are joined with stainless steel screws. A power controlled compressor adjusts its speed to the required power. The highly efficient and extremely quiet running DC Inverter compressor is mounted on anti-vibration and protected against overheating and overclocking. The refrigerant circuit of this air / air heat pump is in addition to the compressor, among others the following components: hot gas exhaust, 4-way diverter valve, specially coated heat exchanger (Clear Fin) of copper tubing with aluminum fins, electronic expansion valve, collectors, filters, check valves, stop valves, Schrader valves and temperature sensors. The device is pre-filled with R410A.
The inverter control ensures a stepless power adjustment during partial load operation. Through this performance optimization energy consumption and thus operating costs are reduced. A controlled fan with DC motor ensures low noise to optimize the condensation temperature. A winter operation is standard guarantees to -15 ° C. The fully automatic microprocessor control systems working optimizing and communicates via bus signals with the connected indoor unit. Current sensor, Noise Killer, Spark killer. Oil return and automatic defrost are guaranteed. A Silent Mode operation can be time-dependent programmed via the remote control of the indoor unit and ensures a sound-reduced operation. The outdoor unit communicates via a bus signal with the connected indoor unit. The power is supplied via the outdoor unit. A bus line ensures the communication between indoor and outdoor units. The electrical connection between indoor and outdoor unit is 4 wires.
Features:
-controlled inverter
-Auto Defrost function in the heat pump operation
-Reduced noise operation ( Silent Mode )
-Compressor Overheating protection
-Overload protection for cooling and heating
-certified ISO 9001, CE approval

Mitsutohi Heavy indoor unit FDTC-VF model 35, Nr.K85273 4-way Euro raster ceiling cassette with panel, 3.5/4.5kW.
The indoor unit is a connection and ready to operate air conditioner for cooling and heating for ceiling installation in euro contact spacing.
A quiet running, anti-vibration mounted, 4-stage DC centrifugal fan with overheating protection takes in the room air via the integrated, regenerable filter unit in the suction panel. The 4-way air discharge of the conditioned air via individiuell adjustable louvers with motorized Deflektorautomatik. The conditioned air is distributed at an angle of 360 ° around the device, thus ensuring an optimal air distribution in the room. The discharge angle of the 4 vanes can be individually and independently set with a wired remote control and fixed in the desired positions when needed. Are optional for the operation of the swing louvers auto functions, memory, or Up / Down is available. On the pressure side, a channel connection for treated air is prepared for the next room supply in the housing. Included in the standard equipment are a quiet-running condensate pump with a maximum head of 600 mm from the lower edge and a float switch for safety shutdown in case of failure of the condensate drain. By easily removable panel corners rapid adjustment of the entire unit to the threaded rods with installed panel is possible.
The device contains all the necessary facilities for automatic operation and monitoring and control instruments. The microprocessor controller with integrated fuzzy logic adapts the power produced to the current conditions and needs in the area quickly and with high stability. The device has a special mode for dehumidification. The icing protection guarantees optimal heat transfer to the heat exchanger. A differentiating self-diagnostic system monitors the system and displays any faults by an alphanumeric code on the remote. The operating status and malfunctions are indicated by different colored LED. An automatic reclosure after a power failure is possible with wired remote control. The control of the device is an alternative to a wired remote control (with integrated weekly timer) or infrared remote control. The required for control via infrared remote control optional infrared receiver can be integrated into any corner of the panel. The operating modes cooling / dehumidification / heating / auto, set temperature and fan speed can be programmed. The device can be switched by an external pulse or on / off signal via a floating contact remote on / off. A sleep timer function turns the unit off after a set duration. The backup function allows automatic operation with standard conditions.
Special Features:
- Euro grid panel dimensions 700 x 700 mm
- Optimum air distribution by Microcomputer controlled air discharge louvre, individually changeable (with cable remote control)
- Quiet operation and minimal 29 dB(A)
- Restart after power failure with cable remote control
- Self-diagnostic system
- Integrated condensate pump with 600 mm delivery height
- Integrated exhaust air connection
-certified ISO 9001, CE approval
accessories: 
-A Variety of remote controls, system controls, installation accessories for AG and IG, electrical accessories and pumps are available as an option, example.:
Operating / alarm
Remote On / Off
CompTrol® - Series
Fresh air adapter
exhaust air adapter
full enclosure
distance frame
Modesty panel for distance frame
- Additional connectivity options are possible through adapter boards , eg:
Superlink®-Bus: SC-ADNA-E
Technical Specifications:
cooling capacity (min.~max.):  3.5 (1.10~3.70) kW
heating power (min.~max.): 4.5 (0.90~4.80) kW
dimension unit (HxBxT): 248x570x570 mm
weight indoor unit: 15.0 kg
dimension panel (HxBxT): 35x700x700 mm
weight Panel: 3.5 kg
power supply: 230/1/50,N,PE V/Ph/Hz
Liquid Line/Device Connection: Ø 6 mm /Ø 1/4"
Suction/Device Connection: Ø 10 mm /Ø 3/8"
Condensate pump, pump head ( from the lower edge ): 600 mm
Condensate line connection: Ø ID/AD 20/26 mm
Fresh air/exhaust air connection , perforated : optional TC - OAS - E + TC - OAD - E / 3 Connection A 100x100 mm
Air filters, long-life filter (washable): yes
fan,number of steps: 4 piece
air flow (Lo/Me/Hi/PHi) cooling: 420/540/570/660 m³/h
air flow (Lo/Me/Hi/PHi) heating: 480/540/600/690 m³/h
Cold air flow, air distribution: 3.5 m
Sound pressure level (.Lo/Me/Hi/PHi - acc JIS) cooling: 30/36/40/41 dB(A)
Sound pressure level (.Lo/Me/Hi/PHi - acc JIS) heating: 32/35/42/43 dB(A)
Reference Data for outdoor unit
cooling: TK 35 °C, FK 24 °C
heating: TK 7 °C, FK 6 °C
SPL : Distance 1.0 m
Reference Data for indoor unit
cooling: TK 27 °C, FK 19 °C
heating: TK 20 °C
SPL : Distance 1.0 m