NORDSIL N Grey aluminium 310 ml, one-component silicone sealant for cold store construction (elastic, neutral hardening)

Elastic single-component silicone sealant NORDSIL N aluminium is suitable for cold store construction. Areas of application NORDSIL N is an elastic, neutral-hardening one-component silicone sealant that remains elastic. Suitable for sealing window, connection and expansion joints Due to the wide adhesion spectrum and the permanent soft elasticity even under extreme conditions - such as high motion absorption, high UV radiation and strong temperature fluctuations - it is suitable for many applications. NORDSIL N is compatible with paints and varnishes according to DIN 52452 T4, also with environmentally friendly dispersion paints and varnishes (self-testing required due to the large number of varnish and glaze types) Tested for microbial metabolism in accordance with DIN 52452 T4. DIN EN ISO 846, procedures A and C After the curing process, a permanent restoring and appropriate adhesion properties are guaranteed, even under extreme environmental conditions. Characteristics: Permanently elastic one-component silicone sealant Neutral system Suitable for sealing window, connection and expansion joints Due to the wide adhesion spectrum and the permanent soft elasticity even under extreme conditions such as high motion absorption, high UV radiation and strong temperature fluctuations, it is suitable for many applications. Free from foreign softeners In addition to our standard colours, we also offer customer-specific solutions based on RAL or NCS colours. The advantages of NORDSIL N - untrimmed, without foreign plasticizers  - Permanent soft elasticity even under extreme loads - Wide adhesion spectrum offers universal application possibilities - Non-corrosive on metals - Abrasion-resistant - recommended and approved according to TOXPROOF criteria (TÜ V Rheinland) - for RAL-compliant installation in accordance with the RAL standard. VDI 6022, Sheet1TECHNICAL VALUES:   Characteristics: Value  Reaction system: Neutral (reacts with humidity)  Standard colours: see colour chart  Spec. Weight: 1,01 g/ml  Application temperature: +5°C to +40°C  Temperature resistance: -50°C to + 150°C  Skin formation time (23°C, 50% rel. humidity: +40°C to +40°C ) LF): ca 7 minutes  curing time (23°C, 50% relative humidity) LF): 3,0 mm in 24 hours 7 days 7 mm  modulus E (100%): ISO 8339 0,40 N/mm2  tensile strength: ISO 8339 1,14 N/mm2  elongation at break: ISO 8339 110 % (fracture pattern 100 % cohesive fracture)  hardness: ISO 868 25 Shore-A . 6 % Permissible total deformation: DIN 52455-3 25 %Processing instructionsPretreatment of the adhesive surfaceAll surfaces must be load-bearing, dry, free of grease and dust. Clean pore-closed, non-absorbent surfaces with cleaner R40. Mechanical cleaning of absorbent mineral surfaces For PVC profiles we recommend our own tests and tests. consult with /N/K/K/F// for further information. Nordsil N adheres to a large number of surfaces without the use of primer (glass, lacquers, varnishes, glazes, anodised, etc.). aluminium, polyester etc.) On porous mineral substrates an adhesion improvement is achieved with primer P, on metallic substrates with primer 1200 OS. joint formationIn the case of glass sealing /N/K/F/- use tape with such dimensions that the joint dimensioning of the DIN 18545 T1 resp. corresponds to the Rosenheim table (minimum cross-section: 3 x 5 mm) In the case of glazing on both sides without tape, the IVD leaflet No. 10 must be observed, whereby the minimum cross-sectional area is 4 x 5 mm. For other joints, the width of the joint must be chosen in such a way that the permissible total deformation of Nordsil N is not exceeded. Pre-stock joints with PE round profile (polyethylene - closed-cell foam) and fix them to the correct joint depth (sealing of joints in accordance with DIN 18540 or DIN 18540). IVD - Leaflet No. 9), do not damage the round cord. In the case of rigid joint backing, tape or polyethylene film, apply to prevent adhesion on three surfaces. Backing materials must be compatible with NORDSIL N in accordance with DIN EN 26927. Unsuitable are raw materials containing tar, bitumen and natural rubber, chloroprene or EPDM based fillers as well as materials based on natural rubber, chloroprene or EPDM; fill Nordsil N without bubbles into the joint. Carefully remove excess glazing agent from the frame and glass immediately afterwards. Ensure that no glazing agent remains on the chamfer. Fresh Nordsil N can be removed with cleaner R40 Restrictions of tar and bituminous surfaces containing tar and bitumen are unsuitable as adhesion grounds. In contact with some organic elastomers such as EPDM, APTK, neoprene, discoloration of the sealant may occur. Enamel and highly fired ceramics can cause contamination. When used on marble and granite, contamination of the edges by ingredients of the formulation may occur. Please use our special natural stone silicone Nordsil M. Nordsil N should not be used in enclosed areas, as it requires humidity to cure. Discolourations as with other sealants occur only rarely Contact with adhesives, other sealants, strong chemicals and in low light areas may cause yellowing. NORDSIL N must not be used for structural glazing facades, insulating glass edge sealant, aquarium production and direct medical or pharmaceutical indication. Form of delivery 310 ml cartridges, 400 ml and 600 ml foil bags Storage timeWith coolers (below + 25~C) and dry storage in closed original packaging, the storage time is 15 months after production if the storage conditions (temperature, relative humidity, temperature, humidity, humidity, etc.) are met. LF) do not vary greatly The expiration month is indicated on the packaging (example: 10/16- to 30.10.2016)Safety instructionsSafety data sheets can be obtained from / N / K / F /. Attention: Please read the EC safety data sheet, the label and the safety advice notes before handling the product for safe processing. We cannot be aware of all applications or conditions of use for your products and do not warrant the suitability of a product for specific applications. You should carefully examine every suggestion for the use of our products in order to see for yourself the satisfactory performance of your application. If our products are to be used in applications requiring a government approval or approval, we will not be able to guarantee that they will be used in accordance with applicable laws. approval, it must be obtained from the user before the product is approved. We only guarantee that products comply with the respective specifications, but we do not warrant or guarantee the suitability of the product for a particular application, or any other express or implied warranties. The user's right and the liability of /N/K/F/ are limited to the reimbursement of the purchase price or the exchange of any product which demonstrably does not have the specific characteristics. The /N/K/F/ is in no case liable to pay damages. Proposals for use are not to be understood as an invitation to infringe existing patent rights.