Mitsubishi Heavy FDS Monosplit Unit Set 230V, No. K85591 (Outdoor unit Hyper Inverter FDC100VNX + indoor unit FDU-VF Model 100), 10/11.2kW, 8kW Heating capacity at -15°C

Mitsubishi Heavy FDS Monosplit Unit Set 230V, No. K85591 consists of an outdoor unit Hyper Inverter FDC100VNX and an indoor unit Channel unit 100-200 Pa static Pressun FDU-VF Model 100,10/11,2kW, 8kW heating capacity at -15°CMitsubishi Heavy outdoor unit Hyper Inverter 230V FDC VNX Model 100, No. K Air/air heat pump unit with inverter technology for up to 3 split-climate indoor units in simultaneous operation Ready-for-connection refrigeration unit for outdoor installation for cooling, but particularly suitable for effective heating operation due to the high available heating capacity at low outdoor temperatures, fast heat supply and high energy efficiency. The components are produced in large series production according to ISO 9001, CE-certified and tested under standard conditions. The device meets the requirements of WHG (outside of water protection areas, below the minimum limit) The housing is self-supporting and consists of a galvanized base frame and easily removable stove-enamelled panels. The "Blue-Fin" coating of the heat exchanger provides protection against corrosion. A power-regulated scroll compressor adjusts its speed to the required capacity The DC inverter compressor is equipped with an oil sump heater, mounted on vibration dampers and protected against overheating and timing. In addition to the compressor u a consisting of the following components: hot gas silencer, oil separator, 4-way switch-over valve, optimised large-area heat exchanger, electronic expansion valves, liquid separator, liquid separator, shut-off valves and Schrader valves High pressure switch, low pressure sensor, temperature sensor. A regulated fan with DC motor ensures low-noise optimization of the condensation temperature. The fully automatic microprocessor control operates systems optimizing and communicates via bus signals with the connected indoor units. Current sensor, Noise Killer, Spark Killer, autom. Oil recirculation and defrost control as well as different coloured LEDs for indication of operating conditions and diagnostics ensure safe operation. The test mode checks the perfect functioning of the system in cooling or heating mode. Pump-down operation can be activated Silent operation ensures soundproof operation Power is supplied via the outdoor unit The electrical connection between the outdoor and indoor unit is 4-wire Technical data: Rated output cooling / heating: 10.0/11.2 kWcooling / heating: 4.0-11.2 / 4.0-12.5 kWHeating output at -15°C: 8.0 kWEER: up to 4.00COP: up to 4.34Power data in accordance with Ecodesign guideline for indoor unit combination: 1 x FDT100VFcooling SEER/Ener Liquid connection: 10 mm (3/8 ") connector Suction gas flow rate: 16 mm (5/8 ")Line length: 100 m Height difference min. /max.: 30/15 mAir flow rate max.: 6000 m³/hSound pressure level max. (1 m, JIS)cooling/heating: 48/50 dB (A)Sound power level cooling / heating: 70/70 dB (A)Dimensions (H/W/D): 1300/970/370 mmNet weight: 105 kgIndustrial range cooling / heating: -15 to 43 / -20 to 20 °CData outdoor unit dependent on connected indoor units and based on standard conditionsCooling: outdoor 35°C, -20 °C, -30°C, -20°C. Split indoor unit ready for connection and operation in recessed ceiling version with duct connection for cooling and heating The air conduction takes place via two vibration damped mounted, a four-stage DC centrifugal fan sucks in the room air through a duct. An overheating protection of the fan motors is integrated The conditioned air is blown out via a duct into the false ceiling. Fresh air connection and one of the duct connection for conditioned air to the auxiliary room supply are prepared in the housing. The customer-specific differing max necessary external pressure of the fan can be adjusted with the RC-E5 or RC-E5 cable remote control. RC-EX1 can be automatically adjusted and preset so that the electrical power consumption of the fan motor can be limited. the standard equipment includes a quiet running condensate pump with a maximum delivery height of 600 mm from the lower edge of the unit and a float switch for safety shutdown in the event of a condensate discharge failure. The device contains all the equipment necessary for automatic operation as well as control and regulating devices. The microprocessor monitors and controls individual components The device has a special control unit for dehumidification The anti-icing protection guarantees optimum heat transfer at the heat exchanger The hot-start and hot-sport function ensure rapid heating of cold rooms after the air conditioner has been started in heating mode. The self-diagnosis system enables fast error detection and indicates possible faults by means of an alphanumeric code on the remote control. Automatic restart after power failure is possible with a cable remote control, the device can be controlled alternatively with a cable or infrared remote control, each equipped with a real-time timer. The operating mode (cooling, dehumidification, heating, recirculation, automatic), setpoint temperature, fan stage and fin pendulum can be programmed. The device can be switched by an external pulse or on/off signal via a potential-free contact Remote On/Off. The device can be controlled alternatively with a wired or infrared remote control. The infrared receiver required for control via infrared remote control is already integrated in the device The optional CompTrol series increases operating comfort and operational safety through central control and monitoring with a connection to central control systems and building management systems. Technical data: Rated capacity cooling/heating: 10.0/11.2 kWNumber of fan speeds: 4 pcs. air volumes (Lo/Me/Hi/PHi)cooling: 1140/1500/1680/2160 m³/hExt Pressure Standard/max.: 10-200 PaAir volume (Lo/Me/Hi/PHi)cooling: 30/36/38/44 dB (A) 1.5 m, JIS standard)Sound power level cooling/heating PHi: 65/65 dB (A)Connection Liquid connection: 10 mm (3/8 ") connector Suction gas connection: 16 mm (5/8 ") connection Condensate drain: ID 25 / AD 32 mmHeight of discharge Condensate pump: 600 mmDimensions Unit (H/W/D): 280/1370/740 mmNet weight Unit: 54 kgData referring to standard conditions and depending on outdoor unit Cooling: outside 35°C, room 27°C/47%RHeating: outside 7°C, room 20°C