Flare Set Jaws Spin F6000 for Diameter 1/4 ", 3/8", 1/2 ", 5/8", 3/4 ", 7/8" Finished in 5 Sec
€131.04*
Do you have some questions about this product?
- Your personal contact person
- Elif Goekce
- [email protected]
- +49 2554 912 983 9
- Nicht das gefunden wonach Sie suchen?
Downloads
- 83-8124610-Datasheet-HHKaeltetechnik - Datenblatt / Datasheet
Suitable for all refrigerants incl. For R410A.
Designed for the most common pipe diameters in the HVAC system. The rotary tool maintains the ductility of the copper / aluminum during buffing and prevents cracks and leaks.
Features:
- Up to 10 times faster than conventional tools
- No deburring required
The turning tools are for use with drills or screwdrivers of at least 1800 rpm and 500 watts or higher for cable drills and 1800 rpm and 18V or higher for cordless screwdrivers. Using the turning tool with less powerful tools can result in smoother performance.
The B & W kit is suitable for buffing 1/4 ", 3/8", and 1/4 " ; and 1/2 "& rsquo; Copper pipes with a max. Wall thickness of 0.8mm as well as 1.0mm wall thickness at 5/8 & ldquo; Copper pipes. If you use the kit for larger wall thicknesses than recommended, it may cause undesirable deformations and assembly problems.
INSTRUCTIONS:
1. Place the brake nut on the metal tube.
2. Attach the Bumble-Knob Kit to the diameter of the drill or screwdriver and make sure it is not loose.
3. Make sure the HAMMER MODE is off. Make sure the pipes are always securely fastened. You can use your other hand to do this. Turn on the unit, push the power lever, and keep the drill / screwdriver at MAXIMUM SPEED.
4. Hold the pipe ALWAYS aligned with the drill / driver and DRY the paddle set inwards, using a CONSTANT PRESSURE, until the stopper passes over the pipe.
5. Hold the pipe in line with the drill / driver and at the same time run the drill / screwdriver at MAXIMUM SPEED. Then remove the B & B kit from the inside of the tube. Remember: The whole process should take no longer than 5 to 7 seconds.
6. Immediately after the BÖHLER process, the tube temperature is very high. Do not overdo. Wait for the tube to cool before touching the bowl. The final result will be a smooth 35 ° bobble, self-standing at 37 ° to 45 ° broom angles. can adjust without tearing or leaking.
7. Insert the nut into the valve of the appliance and use a screw-in wrench for coupling. In doing so, the nut and the valve will form the shingled tube to its final angle and definitive position, without cracking or licking.
SAFETY INSTRUCTIONS:
1. The door sets work with HIGH TEMPERATURE technology; the temperature is due to the friction between the metal tube and the tool. For safety reasons, always assume that the device is hot.
2. Wait for the metal tube to cool before touching the surface of the tube or tool by hand.
3. Always wear protective gloves when working with the Bumble-Knob Set (SFI LEVEL 10 Protective Gloves).
Direct skin contact with the tube or tool can cause serious injury and burns.
4. Note that the broom tool is always well fastened in the used tool (cord or cordless drill).
5. Always wear safety goggles when working with the Bumblebee Set. ANSI Z87.1 Eye Protection (CAN / CSA Z94.3). Occasionally, spills may form and enter your eyes during the bumpy process, causing serious injury, burns, or even loss of sight.
6. Do not wear loose clothing or jewelery, and do not cling to the running tool with long, open hair, as these may entangle in it, which could cause serious injury.
You may also like to Watch Video .
| Manufacturer: | Diverse |
|---|
- 83-8124610-Datasheet-HHKaeltetechnik - Datenblatt / Datasheet
More articles from Diverse to look at
Artikel Zubehör
